Wet Look Appearance, High Gloss Finish
Cobble Loc HI-Gloss is the most advanced technological
sealer in waterborne protection for concrete, brick pavers,
and many other surfaces. Cobble Loc Hi-Gloss may be
used over most porous surfaces as it has excellent
adhesion, water and marking resistance. Unlike other
clear finishes, Cobble Loc Hi-Gloss has excellent
coverage, and resistance to chemicals, bleach, and acids.
Cobble Loc also locks joint sand in place, helps prevent
ant hills from forming and weed growth.
Applications
Use Cobble Loc Hi-Gloss on driveways, pool decks,
entryways, walkways, median strips, and patios, where a
gloss finish is desired.
Cobble Loc Hi-Gloss is not recommended for pavers
installed over a solid surface or on surfaces where
moisture is unable
Characteristics & Technical Data
% Solids by Weight (+/- 3%): 43%
QUV (ASTM D G-54): 2,000 hours
with no gloss loss
WT./Gal 8.75 lbs.
Coverage: 200-300 SqFt/Gal
@ 3mil DFT
Pot Life: 2 Hours
VOCs: <50 G/L
Properties & Special Features
- Eco friendly & emits super low VOCs.
- Pressure clean and seal in the same day.
- Locks down paver joint sand.
- Inhibits mold, weeds and ant hills.
- Catalyzed product that resists chemicals and oil.
- Can be used on almost all floor surfaces.
- Top coat for colored sealers and surface treatments
- such as Coloron, Colorcrete, Antique Stain, TD One
- Step & Texture Deck.
Directions
Before You Begin: Surfaces must be clean and free of
any contaminants before sealing. Cobble Loc Hi-Gloss
performance is directly related to how thoroughly the
surfaced is prepared. Do not apply when the temperature
of the air or the surface to be coated is below 50°F, or
above 100°F. Testing on a small area of your surface is
always recommended to ensure desired results.
Surface Preparation: Smooth concrete must be etched.
Scrape and sand all loose material prior to application.
Cobble Clean, Cobble Prep and Cobble Oxhide may be
used for specific cleaning situations.
Mixing Instructions: Cobble Loc Hi-Gloss is a two com-
ponent kit. Part A must be mixed with Part B. A 1 gallon
kit includes a quart of Part B & a 5 gallon kit includes a
short filled 5 gallon pail and a one gallon pail of Part B.
Finally dilute one part of Cobble Loc Hi-Gloss mixed
sealer with one part water. (Mix will become thick, but will
flow immediately after adding water). For best results, it is
recommended to mechanically mix with a power mixer for
a minimum of 10– 15 minutes, before applying.
Applications
Roller: Apply with a 3/8” to 3/4” nap roller cover. Avoid
over rolling. Always maintain a wet edge. Airless Sprayer: Spray by overlapping each pass.
Always apply in an even film deposit and maintain a
working wet line; do not over-apply.
On Bare Surface: One and sometimes two thin coats (2
dry mils) provide the best results on uncoated surfaces.
Over Previously Sealed: One coat is recommended.
Coverage
1 gallon covers 200 to 300 square feet per coat. Coverage
will depend on surface porosity, joint width and application
method. Second coat will take slightly less product.
Curing Information
Dry To Touch: 2 to 6 Hours (varies with conditions)
Recoat: 2 to 6 hours
Full Cure: 48 to 72 Hours
Disclaimer
All Surface Logix products are manufactured with the
finest raw materials. It is the applicator’s responsibility to
determine the appropriate use of the product.
All recommendations and suggestions are made without
guarantee, since conditions of use are beyond our control.
Data Sheets
